Shopping Cart Cover

This Super Simple Shopping Cart Cover is soft and sanitary for your little one. You can even attach toys to keep baby entertained, and he won’t be able to toss them on the floor!

How to:

1
Cut one yard of fleece into the following pieces. You’ll have a total of four pieces: a large 20×26 inch rectangle that will be the Seat & Front, a 20×20 inch square that will be the Back, and two 8×13 inch Side Pieces. It’s important that you use fleece, because this project has raw edges and fleece won’t fray.

2
We’ll start by making slits for the straps  on the square Back Piece. Mark 3 inches in from the sides and 2 inches up from the bottom edge. We’re going to make these slits about 8 inches long, because some carts have the straps down low by the seat and some have them attached to the top of the back. Make one slit on the left and one on the right.

3
Next we’ll add elastic to the top of the Back Piece, so that it will slide over the back of the cart seat and keep the cover from sliding. Add a 1-inch-wide piece of elastic to the top of the Back Piece, on the wrong side of the fabric. It goes on the short end farthest from the slits. Stretch the elastic taut as you sew with a zig-zag stitch.

4
Measure 12 inches up from the bottom edge of the Back Piece, and fold the elastic edge down to that mark. Next sew the left and right folded sides, to create an elasticized pocket area. Use a 1/2 inch seam throughout this tutorial. Wrong sides should be together.

5
Put the Back Piece aside and get out the large seat rectangle.  Pin a Side Piece to the left and right long sides of the Seat Piece. Line up the short top edge of the Side Piece with the top short edge of the Seat Piece. Right sides should be together. Sew the long side edges on both the left and right sides with a straight stitch.

6
Now we’ll add the Back Piece. Lay the Back Piece face down on the Seat Piece, matching up the top edge. You will be pinning the end without the elastic to the top center of the Seat Piece. (You aren’t doing anything with the Side Pieces at the moment.) Sew together with a straight stitch.

7
Your project should now resemble a cross shape. Next we’ll pin the top of the Side Piece to the edge of the Back Piece. Fold the Side Piece upward and line the edge up with the edge of the Back Piece. You will only be sewing 6 inches from the seam at bottom, leaving a loose flap of fabric at top that will fold over the side of the cart.

8
Sew the Side Piece to the Back Piece, with a seam that is 6 inches long. This will create a box corner.

9
Now we need to add the ribbon ties. This will allow you to tie the cover onto the cart for extra security. Cut 4 ribbons that are 10 inches long.

10
Fold under the edge of one ribbon to prevent fraying, then pin it towards the bottom of a Side Piece. Pin it along the side edge, about 3 inches from the bottom. The ribbon should be face-up and pointing outward. Sew with a zig-zag stitch. Repeat with another ribbon on the other Side Piece.

11
Pin the other two ribbons to the bottom center edge of the Side Pieces. Again, the ribbons should be face up and extending outward.

12
Line up the edges of the Side and Seat Pieces and sew together the full length of the Side Piece’s edge. Again, this will create a box corner, with the ribbons poking outward.

13
Carefully singe the ends of the ribbon with a lighter to prevent fraying.

14
Now we’ll cut the circles for the leg holes. I made the center of my circle 8 inches down from the seam that joins the Back and Seat pieces. Make the circles rather large for ease of use.

Your shopping cart cover could be finished right now, it’s basic but functional. However, there are a few finishing touches that will make your cart cover look more professional.

1
First, you can finish the edges of the slits and leg holes with ribbon trim. Fold under the raw edge of a piece of ribbon, and fold the ribbon in half around the raw edge. Stitch in place. (This isn’t mandatory since the fleece won’t fray, but it does make your project look nice.)

2
Second, you can add Velcro that will wrap around the shopping cart handle. If you don’t add Velcro, the flap of fabric will hang loosely over the handle. To add Velcro, cut 3 pieces about 2 inches long, and sew horizontally to the underside bottom edge of the fabric.

Add the coordinating Velcro about 3 inches down on the underside of the fabric. Sew these pieces vertically. This will allow you to adjust for variations in handle sizes… Target, for example, has very large cart handles.

3
Third, you can add a ribbon toy bar. This is simple to do. Fold under the raw edges of a ribbon strip. Add two more pins at regular intervals. Zig-zag stitch the ends, then tack down where you had pinned. This creates three loops for adding toy rings. You could also attach a Tippy Sippy leash so your little one doesn’t drop his cup or bottle on the floor.

To Use:

To use the Super Simple Shopping Cart Cover, slide the elastic over the back of the seat. Tie the corner ribbons, and attach the Velcro around the handle.

This shopping cart cover rolls up into a tidy packet. Start rolling from the end without the elastic, then tuck the edges inside of the elastic pocket area.

Click to check out Made By Marzipan’s other sewing projects for baby.

Made By Marzipan may have received product or payment for this post. Posts may contain affiliate links. Disclosed in accordance with the Federal Trade Commission's 16 CFR, Part 255.

One thought on “Shopping Cart Cover

  1. Marsha says

    What a brilliant idea! I hate putting my little gems in the filthy carts. I added some back support because my girls are just little. I’ve added a photo to the site.

    Thanks a ton
    Marsh, David, Kara and Maggie

Leave a Reply

Your email address will not be published.